Essential Plumbing Tips for Installing a Bathtub
Essential Plumbing Tips for Installing a Bathtub
Blog Article
Here down the page you can discover a bunch of superb expertise relating to Installing A Bathtub.

Setting up a bathtub isn't specifically rocket science, however it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably tough job. If the old bathtub is conveniently accessible, the project can relocate quickly; if you have to open a wall to eliminate the old bathtub and also place the new tub, the task is much harder. In either instance, the project is within a residence handyman's abilities, although you will certainly require a helper to leave the old tub and also embeded in the brand-new one. Make certain you have actually certified on your own for the work as well as fit attempting it. Rather than employing a professional to take control of a halfway-completed project, it is better to consider employing one prior to you begin. Opportunities are you may need an expert plumber to make tube links.
This write-up will certainly aid you install a brand-new bath tub in your restroom if you have already bought a new bathtub and also do not need to change the plan of your previous water system pipes.
Your devices and also product list ought to comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you need to do is detach the water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly problematic as a result of the restricted gain access to that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will come from the pipes. Once the supply pipes have actually been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers are in area between the faucet and the sink. Safeguard the tap in position with the producer provided backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former type needs to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Using both wood boards under its feet, put the bath tub in the required position. The wooden boards are practical in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the level and also adjusting the feet on the bath tub until the level reviews level.
To mount taps, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply as well as examine all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub and also inspect the overflow electrical outlet as well as the regular outlet for leakages.
Lastly, deal with the bath paneling as described in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait until the bathtub has been used at least once as this will certainly resolve it right into its final placement.
Planning for the Installment
To start with, the sustaining framework supplied with the bath must be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to stop stress on the bath tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now be ready to be suited its last position.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, causing the water to permeate the wall surface in between the bathroom and the tiling, leading to problems with dampness and feasible leaks to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes and also cartridges, and can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to permit the motion experienced when the tub is in use. The sealant can crack relatively very early if you do not think about this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily offered on the marketplace. It is a good idea to fit the floor tiles using waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you like more info about How to Install a Bathtub? Write a review below. We'd be delighted to listen to your thoughts about this posting. In hopes that you come back again later on. Do you know somebody else who is fascinated with the niche? Why not promote it. I appreciate reading our article about Tools You Need to Install a New Bathtub .
Always ready, contact! Report this page